|
|
Post by kamaradski on Aug 23, 2020 19:19:19 GMT
Hi all, i wanted to use VJOY in combination with UJR to remap some controllers, but i'm runbning into the following problem:
1) When installing VJOY it appears to get get stuck in the installer. But with alt-tab you can see it actually has a second window open in the background. When using the taskmanager to force close the installer, i can in a split second see that i think this ins a message about " installation success".
2a) when i next open UJR v6.10 it shows me a message: ERROR could not find the VJOY Registry Key. VJOY does not appear to be installed...
2b) in previous installation attempts i have also seen: ERROR in we have found VJOY in PATH but it appears to be an outdated version...
i'm on win 10 pro 1909
Is there anything i can do to get this fixed ? thanks in advance for any help.
|
|
njz3
New Member
Posts: 22
|
Post by njz3 on Aug 24, 2020 5:24:31 GMT
Hi,
First, which version of vJoy do you use ?
Next, once vJoy is installed, did you configure it ? Have you then tried to run vJoy Monitor and the vJoy Feeder example to make sure your installation does work ?
If from this point everything is good, then the problem might be related to UJR.
|
|
|
|
Post by Boeng on Aug 25, 2020 0:53:14 GMT
Running into the same Problem. Vjoy tells me Version 2.19. It can be configured, vjoymonitor and feeder example works fine. But the Installation window never closes and UJR ends with the above stated error. Plz help.  |
|
|
|
Post by kamaradski on Aug 25, 2020 17:04:52 GMT
Hi, thanks for the reply.
vJoy v2.1.9
UJR v6.10 (ADHD v 3.3.4)
Feeder works, and any sliders that I move around in the feeder can be observed in the monitor in realtime. So I think this looks good. I guess this is the bare minimal required to make UDR work, right?
|
|
|
|
Post by kamaradski on Aug 25, 2020 17:15:13 GMT
Crazy, i think it now works. what did i do: - install vJoy again on top of the existing (not working) installation (move the installer window in some corner of the screen) - wait for the drivers to be installed (you hear the " usb-connect" ping) - leave the installer window open! - open vJoy, click " add device", get prompted for a re-start - after restart vJoy was still open, and the " installation success" window was visible. click " ok" here - open UJR and it magically came to live Hope this helps others. |
|
|
|
Post by friendofjah on Sept 6, 2020 12:53:55 GMT
Crazy, i think it now works. what did i do: - install vJoy again on top of the existing (not working) installation (move the installer window in some corner of the screen) - wait for the drivers to be installed (you hear the " usb-connect" ping) - leave the installer window open! - open vJoy, click " add device", get prompted for a re-start - after restart vJoy was still open, and the " installation success" window was visible. click " ok" here - open UJR and it magically came to live Hope this helps others. Hi kamaradski - I followed your instructions to install vJoy Version 2.1.9 on my Windows 10 64 Bit PC. I got up to the step where you said, "open vJoy, click " add device", get prompted for a re-start". I assume when you say Open vJoy you mean click on Configure vJoy correct? I did so and there is no "add device" button only Apply; Undo and Delete Device. I clicked on Apply and then was prompted to restart Windows. After doing so, vJoy was not still open, and the " installation success" window was not visible and click " ok" here was not there either. Any ideas on what I'm doing wrong here? This is driving me %$#@*! nuts! Thanks in advance for any help provided. |
|
|
|
Post by tofod on May 7, 2021 22:24:07 GMT
Hi guys,
add same kind of problem and finnaly found that UJR isn't supported anymore.
Check for UCR .. it works out of the box with vJoy on W10
Hope this help
|
|
|
|
Post by Daltondal on Dec 9, 2021 2:03:58 GMT
|
|
|
|
Post by Daltondal on Dec 9, 2021 2:04:46 GMT
|
|
|
|
Post by Daltondal on Dec 9, 2021 2:05:32 GMT
|
|
